Concrete Grinder Rental Electric Double Disc (Edco) C5GE

•EDCO Grinders - Proven in over 50 years of use. Accept no substitute! •11" Working width will grind approximately 200-250 sq. ft. per hour at 1/32" with EDCO Dyma-Serts •Round shroud gets tight against walls •Easy-rolling 10" steel-core, rubber wheels •Lifting eye for easy loading and unloading •Includes 1 multi-accessory discs, which accept Dyma-Serts, Strip-Serts and all other grinder accessories •3 grinding accessories required per loading •2" Vacuum port and water port •25ft. Power cord attached with cord hanger •Accessory Toolbox tray •Side-mounted lifting handles •Easy access to grease fittings •30lb. weight pack standard •Rugged and easy to maintain Ideal for: •Areas less than 1,500 square feet •Residential applications •Grinding concrete •Repairing damaged concrete slabs •Removing urethanes or epoxy thin-coats •Leveling high spots or surface imperfections •Smoothing rough surfaces, rain marks or trowel marks •Removing mastics, thin-sets, paint build-ups, resins and more

EDCO SEC 1.5L Single-Disc Grinder Specifications EDCO SEC-1.5L Single Disc Floor Grinder Specifications Model SEC-1.5L Part # 50200 Power Electric Horse Power 1.5 HP, 115/230 V Phase Single Amps 17.2/8.6 *RPMs 580 Belts Cgd. "V" Belts Length 41" Width 24" Height 36" Weight 152 lbs. PRODUCTION RATE: 11" Working width Will Grind Approximately 200-250 Sq. Ft per Hour at 1/32" with EDCO Dyma-Serts™ INCLUDES: 1-Multi Accessory Disc, 2" Vacuum Port & Water Port REQUIRES: 3-Grinding Insert Accessories per Loading IDEAL FOR :          - Areas less that 1,500 square feet                            - Residential applications                            - Removing mastics, sealers or smoothing concrete * RPMs are based on the machine's accessory speed.

2EC/2GC - Dual-Disc Grinder How to Load Multi-Accessory Disc Properly loading the accessories is important. Improper loading can cause damage to the accessories. Do not attempt to grind the concrete with the multi-accessory disc. A clear indication that a customer has done this is when a gray/silver mark on the concrete surface is noticed. Use provided wedges when loading the accessories. When loading the wedges, they must be between the accessory and the inner wall of the disc. Dyma-Serts can be loaded in either direction. However it is very important that after a day’s rental that the Dyma-Serts be flipped 180 degrees and then re-inserted. Failure to do so will result in uneven wear of the Dyma-Serts. Strip-Serts must be inserted one way and one way only. The spring end of the inserts or the open end of the Strip-Sert must be pointed towards the center of the disc. The sharp end of the Strip-Serts should be facing the open end of the disc. All other accessories can be loaded in either direction. (i.e. grinding stones, scarifier assemblies & wire brushes). How To Grind Concrete Start Up Before starting, push down on the handle just enough to release pressure from the grinding disc. Do not lift the disc from the slab surface. The slight weight shift will aid the motor in reaching operating speed without an excessive start-up current draw. To start the motor, switch to the "Start" position in the motor starter box. Once the motor reaches operational speed, allow the grinder to settledown to the slab and begin grinding. Grinder Wheel Carriage Positioning The grinder has two wheel positions — one for grinding and one for transport. When the wheels are in the forward most position, this is the transport mode. Do not grind in this position. Grinding in this position will cause damage to the accessories. Grind only with wheels in the rear position. The grinder should always be moved in a side to side motion when grinding. By doing so, you eliminate many of the swirl marks that are created. Weight helps with the grinding process as it allows the accessories better contact with the surface. The single-disc grinder’s max weight is 50 lbs for the electric model and 100 lbs. for the gasoline model. The dual-disc grinder’s max weight is 100 lbs for the electric model and 200 lbs. for the gasoline model. The grinder is designed for wet or dry grinding. Dry grinding is preferable because the accessories constantly are in contact with the surface. EDCO grinders are equipped (standard) with a 2" or 3" vacuum port (depending on the model). Always use a high volume industrial vacuum with a grinder to control the large volume of airborne dust when grinding dry. When wet grinding, water is only needed to control dust and does not act as a coolant. Lightly dampen the floor or use a fine mist to control dust. Excess water will only create clean up problems.

See Brochures/Manuals - "Operation & Safety Manual."