Multiquip HBC19B Rebar Cutter, Hand Held, Electro-Hydraulic, 3/4" (6) Max., 115V/60Hz

Safety Information

Multiquip HBC19B Rebar Cutter

FOR YOUR SAFETY AND SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

NOTICE

This manual has been developed to provide complete instructions for the safe and efficient operation of this equipment.

Before using this equipment ensure that the operating individual has read and understood all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three Safety Messages shown below will inform you about potential hazards that could injure you or others.
The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER

You WILL be KILLED or SERIOUSLY INJURED if you DO NOT follow these directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if you DO NOT follow these directions.

CAUTION

You CAN be INJURED if you DO NOT follow these directions.

HAZARD SYMBOLS

Potential hazards associated with the operation of this equipment will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

WARNING — Respiratory Hazards

ALWAYS wear approved respiratory protection when required

CAUTION — Rotating Parts Hazards

NEVER operate equipment with covers or guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to prevent injury.

CAUTION — Accidental Starting Hazards

ALWAYS place the equipment ON/OFF switch in the OFF position when the
equipment is not in use.

CAUTION — Eye and Hearing Hazards

ALWAYS wear approved eye and hearing protection.

CAUTION — Equipment Damage Hazards

Other important messages are provided throughout this manual to help prevent damage to your equipment, other property, or the surrounding environment.

WARNING — Read This Manual

Failure to follow instructions in this manual may lead to serious injury or even DEATH! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only.

GENERAL SAFETY

 DO NOT operate or service this equipment before reading this entire manual.

 This equipment should not be operated by persons under 18 years of age.

 NEVER operate this equipment without proper protective clothing, shatterproof glasses, steel-toed boots and other protective devices required by the job.

 NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

 NEVER operate this equipment under the influence of drugs or alcohol.

 NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

 Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

 Whenever necessary, replace nameplate, operation and safety decals when they become difficult to read.

 ALWAYS check the equipment for loosened threads or bolts before starting.

 MAINTAIN equipment is a safe operating condition at all times.

 KEEP bystanders, children, and visitors away while operating the equipment. Distractions can cause loss of control.

 DO NOT wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Rotating parts can cause injury if contacted.

 ALWAYS keep work area clean and free of foreign matter and debris. Also keep work area well lit.

 NEVER operate the equipment in an explosive atmosphere or near combustible
materials. An explosion or fire could result causing severe bodily harm or even
death.

 DO NOT overreach. Keep proper footing and balance at all times.

 NEVER leave the equipment unattended. When not is use, before servicing, and when changing accessories, always unplug the equipment from the power source.

 USE this equipment for its intended purpose only.

 KEEP equipment clean for better and safer performance. Keep handles dry, clean, and free from oil and grease.

 INSPECT the equipment after each use. Replace any damaged or worn parts immediately. Do not use equipment if defective.

 If a malfunction occurs, immediately unplug the equipment from the power source and correct the problem. If problem cannot be corrected, contact the
nearest MQ service center.

 ALWAYS store the equipment in a clean, dry location out of the reach of children.

EMERGENCIES

 ALWAYS know the location of the nearest fire extinguisher.

 ALWAYS know the location of the nearest first aid kit.

 In emergencies, always know the location of the nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in case of emergency.

ELECTRICAL SAFETY

■ ALWAYS test the POWER switch on the equipment before operating. The purpose of this switch is to shut down the power.

■ NEVER use a extension cord that is frayed or damaged where the insulation has been cut.

■ NEVER carry the equipment by its power cord or disconnect it by yanking the cord from the power outlet.

■ ALWAYS make certain that the proper extension cord has been selected for the job. See Extension Cord Gauge Selection Table.

■ NEVER allow power cord to lay in water.

■ NEVER stand in water while operating the equipment.

■ When connecting the unit to a power receptacle, make sure the receptacle circuit is connected to either a GFCI receptacle or a receptacle protected by a 20 amp circuit breaker
.
■ When plugging the unit into a power receptacle, check the nameplate for the correct operating voltage.
Operating the rebar bender at the wrong voltage will damage the electrical components. ALWAYS read the nameplate before applying power.

■ This unit is equipped with a 3-prong male power plug.
DO NOT use a 2-prong adapter when plugging into a wall outlet. This will defeat the purpose of the ground circuit. If the plug does not fit into the receptacle, contact a qualified electrician to install a 3-conductor wall
receptacle (outlet).

■ Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electrical shock if your body is grounded.

■ DO NOT expose the hydraulic power unit to rain or wet conditions. Water entering the power unit will increase the risk of electrical shock.

■ When operating the unit outdoors, be sure to use the appropriate outdoor extension cord. This type of extension cord reduces the risk of electrical shock.

■ ALWAYS remove the AC power cord from the power source before performing any service or maintenance on the unit. This preventative safety measure reduces
the possibility of accidental starting.

 When operating near an arc welder, it is important the both the unit and the welding equipment be connected to the same earth ground. If they are not, server damage to the unit, particularly to the power cord could occur.
Personal injury may also occur.