Multiquip CV2B Concrete Vibrator Motor 2 HP, 230V w / Out Plug, Electric

Safety Information

Multiquip CV2B Concrete Vibrator Motor

Safety Information

Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.
Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you about potential hazards that could injure you or others. The safety messages specifically address the level of exposure to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

GENERAL SAFETY

CAUTION

NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations

Avoid wearing jewelry or loose fitting clothes that may snag on the controls or moving parts as this can cause serious injury.

NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

NEVER operate this equipment under the influence of drugs or alcohol.

ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.

Keep work area well lit.

No one other than the operator is to be in the working area when the equipment is in operation.

DO NOT use the equipment for any purpose other than its intended purposes or applications.

NOTICE

This equipment should only be operated by trained and qualified personnel 18 years of age and older.

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest fire extinguisher.

ALWAYS know the location of the nearest first aid kit.

ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fi re department.
This information will be invaluable in the case of an emergency.

VIBRATOR MOTOR SAFETY

DANGER

ALWAYS wear rubber insulated gloves and boots when holding the flex shaft during operation. The possibility of electrocution exists causing equipment damage and
severe bodily harm even death!

DANGER

If applicable, periodically check insulation resistance as referenced in maintenance section. The possibility of electrocution exists causing equipment damage and severe bodily harm even death!

WARNING

NEVER attempt to run the core outside the casing assembly for any reason.

CAUTION

DO NOT overreach. Keep proper footing and balance at all times.

DO NOT carry plugged-in motor with finger on the switch.

NEVER carry the motor by the cord. Use the carrying handle.

ALWAYS check the vibrator motor for loosened hardware such as nuts and bolts before starting.

Keep the cord from heat, oil, and sharp objects.

DO NOT overload the motor. It will do a better and safer job at the rate for which it was designed.

DO NOT expose vibrator motor to rain.

DO NOT use vibrator motor in damp or wet locations without proper electrical circuits.

ALWAYS keep clear of rotating or moving parts while operating the vibrator motor.

NEVER leave the machine unattended while running..

ALWAYS disconnect the motor from the power source when not in use, before servicing, and when changing flexible shafting and vibrator heads.

Allow the vibrator motor to cool before servicing. Contact with hot components can cause serious burns.

Before each use, ALWAYS check the motor to make certain that there are no damaged parts and that all parts function properly (such as switch, cord housing).
If any damage or malfunctioning parts are found, have them repaired or replaced by an authorized service facility.

NOTICE

Secure forms. Make sure the form work is well made and braced to withstand the stresses made by vibration.

Keep vibrator motor clean for better and safer operation.

ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

Use only factory-authorized replacement parts.

Store idle vibrator motor. When not in use, motor should be stored in a dry, safe storage area.

ELECTRICAL SAFETY

CAUTION

Prevent body contact with grounded surfaces such as pipes, reinforcing bar, etc.

When applicable, use a protection wiring device, such as a Ground Fault Circuit Interrupter, for the protection of personnel.

Operate electric motor only at the specified voltage indicated on the nameplate.

DO NOT spray water onto electric motor.

DO NOT yank the cord to disconnect it from the receptacle. Grasp the plug itself to disconnect it.

ALWAYS make sure the ON/OFF switch on the electric motor is in the OFF position when not in use and before inserting the power plug into an AC receptacle.

Before plugging the motor into a power source, ALWAYS remove any wrenches or other tools from the motor, shaft, and head that were used for assembly.

Power Cord/Cable Safety

DANGER

ALWAYS use a grounded 3-wire extension cord that has a 3-prong grounding plug, and a 3-pole receptacle that accepts the plug on the concrete vibrator motor.
DO NOT REMOVE THE GROUNDING PIN FROM THE PLUG!

NEVER let power cords or cables lay in water.

NEVER use damaged or worn cables or cords when connecting equipment to generator. Inspect for cuts in the insulation.

NEVER grab or touch a live power cord or cable with wet hands. The
possibility exists of electrical shock, electrocution or death.

Make sure power cables are securely connected.
Incorrect connections may cause electrical shock and damage to the vibrator motor.

CAUTION

Ensure that cables and cords will not be tripped over.

NOTICE

ALWAYS make certain that proper power or extension cord has been selected for the job.

Use only extension cords that are intended for outdoor use and so marked.

Use only the gauge wire and length of cord recommended for the motor size. If in doubt, go to the next heavier gauge.
(The smaller the gauge number, the heavier the cord.)

ENVIRONMENTAL SAFETY/DECOMMISSIONING

NOTICE

DO NOT pour waste or oil directly onto the ground, down a drain or into any water source.

Contact your country's Department of Public Works or recycling agency in your area and arrange for proper disposal of any electrical components, waste or oil
associated with this equipment.

When the life-cycle of this equipment is over it is recommended that the head
casing and all other metal parts be sent to a recycling center