Multiquip MGX12325 Vibrator Assembly, 120V Motor, 0.90" (23mm) Head, 9.5 Length and 8.2' (2.5m) Shaft

Safety Information

Multiquip MGX12325 Vibrator

Safety Information

DO NOT operate or service the equipment before reading the entire manual. Safety
precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you about potential hazards that could injure you or others. The safety messages specifically address the level of exposure to the operator and are preceded by one of four words:
DANGER, WARNING, CANTION or NOTICE.

DANGER

Indicates a hazardous situation which, if not avoided, Will result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided, Could result in DEATH or SERIOUS INJURY

CAUTION

Indicates a hazardous situation which, if not avoided, Could result in Minor or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

PERSONAL SAFETY

CAUTION

Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury

Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal
injuries..

Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on can cause accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

DO NOT overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.


GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

NOTICE

The term "power tool" in the warnings refers to your mains-operated (corded) power tool.

WORK AREA SAFETY

NOTICE

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.

No one other than the operator is to be in the working area when the equipment is in operation.

DO NOT use the equipment for any purpose other than its intended purpose or application.

This equipment should only be operated by trained and qualified personnel, 18 years of age and older.

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest fire extinguisher.

ALWAYS know the location of the nearest first aid kit.

ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fi re department.
This information will be invaluable in the case of an emergency.

MOTOR and FLEXSHAFT SAFETY

DANGER

ALWAYS wear rubber insulated gloves and boots when holding the flexshaft during operation. The possibility of electrocution exists causing equipment damage and
severe bodily harm even death!

DANGER

If applicable, periodically check insulation resistance.
The possibility of electrocution exists causing equipment damage and severe bodily harm even death!

WARNING

NEVER attempt to run the core outside the casing assembly for any reason.

CAUTION

DO NOT carry plugged-in motor with finger on the switch.

NEVER carry the motor by the cord. Use the carrying handle.

ALWAYS check the vibrator motor for loosened hardware such as nuts and bolts before starting.

Keep the cord from heat, oil, and sharp objects.

DO NOT overload the motor. It will do a better and safer job at the rate for which it was designed.

DO NOT expose vibrator motor to rain.

DO NOT use vibrator motor in damp or wet locations without proper electrical circuits.

DO NOT immerse the motor part in concrete.

ALWAYS keep clear of rotating or moving parts while operating the vibrator motor.

NEVER leave the machine unattended while running.

ALWAYS disconnect the motor from the power source when not in use, before servicing, and when changing flexible shafting and vibrator heads.

Allow the vibrator motor to cool before servicing. Contact with hot components can cause serious burns.

Before each use, ALWAYS check the motor to make certain that there are no damaged parts and that all parts function properly (such as switch, cord housing).
If any damage or malfunctioning parts are found, have them repaired or replaced by an authorized service facility.

NOTICE

Secure forms. Make sure the form work is well made and braced to withstand the stresses made by vibration.

Keep vibrator motor clean for better and safer operation.

ALWAY store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

Use only factory-authorized replacement parts.

Store idle vibrator motor. When not in use, motor should be stored in a dry, safe storage area

ELECTRICAL SAFETY

CAUTION

Power tools must match the outlet. never modify the plug in any way. DO NOT use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

DO NOT expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.

DO NOT abuse power cord. never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

This unit is double-insulated. The double-insulation between the electric-conducting part and the outside frame makes grounding unnecessary. However, if parts are replaced with wrong parts or assembled incorrectly, the vibrator may become unsafe to operate. Use only Multiquip recommended replacement parts.

When applicable, use a protection wiring device, such as a Ground Fault Circuit Interrupter, for the protection of personnel.

Operate electric motor only at the specified voltage indicated on the nameplate.

DO NOT spray water onto electric motor.

DO NOT yank the cord to disconnect it from the receptacle. Grasp the plug itself to disconnect it.

ALWAYS make sure the ON/OFF switch on the electric motor is in the OFF position when not in use and before inserting the power plug into an AC receptacle.

Before plugging the motor into a power source, ALWAYS remove any wrenches or other tools from the motor, shaft, and head that were used for assembly