Multiquip / Mikasa Rammax RX1575 Roller, Articulating Trench, Walk-Behind, W/ Drum Extension, Yammar



Safety Information

Multiquip / Mikasa Rammax RX1575 Roller, Articulating Trench, Walk-Behind

General working safety

● The roller may only be used for driving on and compacting loose top layers (gravel, earth). Other uses are prohibited.

● Rollers may only be operated with all safety devices operating. Manipulation or
disregard of safety devices and regulations invalidates the CE conformity.

● Before starting every shift, check the effectiveness of the operation and safety devices and that the protection devices are in place.

● Check the steering and brakes when you start work. If defects are apparent, roller operation is not permitted.

● If you identify any defects on the safety system or defects that impair safe operation of the equipment, inform your supervisor immediately. The roller may no longer be operated.

● If you identify any defects which endanger safe operation, cease operation immediately.

● Only perform work on and clean the roller if it is stationary and secured from
rolling away.

● Switch off the engine when filling the fuel tank. Do not fill up fuel in enclosed spaces. No open flames.

● Do not vibrate on slopes or inclines where there is a hazard of slipping or overturning.

● Do not drive on slopes that are steeper than the maximum climbing capacity of
the equipment. Always drive the roller carefully perpendicular to the slope dip.

● Do not vibrate inside buildings and on unstable ground.

● The driving and working field of view must not be obstructed in any way.

● Switch off the engine before leaving the roller. Secure the roller against unauthorized start-up and rolling away.

● Take suitable visible measures to secure parked rollers that pose an obstruction.

● Never work under the influence of drugs, alcohol or medicines that impair consciousness.

● Only operate the roller in good general light conditions and good workspace illumination.

● The workplace of the operator is located at a safe distance of at least 2m.

Roller operation

DANGER

Rollover hazard when driving the roller!

• Only start the roller using the handheld transmitter.

• Personnel may not stand in front of or behind the roller while it is in operation.

• Persons necessary for operations at the sides of the equipment must remain at a safe distance of at least 2 m.

Shear points

● When closing the hood ensure that no objects are situated between the hood and
the chassis.

● Take care that nothing is jammed in the joint plates when rotating the roller drums.

● Do not put hands between the roller drum and support during operation.



DANGER

Danger to life through tipping or slipping of the roller! The edges of filled areas may give way!

• Only travel directly up or down slopes.

• Do not drive across slopes.

• Keep your distance to embankments and edges!

• Do not drive at an angle into or out of the trench.

• Park the roller on slopes only in such a way that it cannot overturn.

• Use the roller on slopes only in such a way that it cannot overturn.

• The roller drums have very poor adhesion on snow and ice. Driving or working on a slope in snow or ice is prohibited.

• Damp and loose surfaces reduce the traction of the machine on upward and downward grades considerably. Adapt the speed of the machine to the terrain when driving on grades.

• The nature of the ground and weather conditions can negatively affect the climbing ability of the machine.

Never drive on slopes that are steeper than the maximum climbing ability of the machine

Construction site conditions can have a negative effect on stability and the tipping angle.

DANGER

Crushing hazard in the area of the articulated joint

• During operation, there is always a crushing hazard in the area of the articulated joint. Therefore, it is not permitted for persons to be in this area during operation. In general, a safety distance of at least 2 meters to the machine must be maintained during operation.

DANGER

Crushing of toes through careless handling of the roller!

• Wear safety shoes when working with the roller in order to help avoid crushed toes.

DANGER

Danger of accident through improper operation of the roller!

• Read the operating instructions before operating the roller.

• Adhere to the safety regulations at all costs.

• In case of lack of clarity, contact your authorized dealer

Noise levels

WARNING

Hearing damage due to continuous noise level!

Depending on the use of equipment it is possible that the allowed noise level of 85dB (A) will be exceeded.

• Wear ear protectors in accordance with national accident prevention regulations when working at higher noise levels.

The following noise level measurements were carried out by an accredited testing
and monitoring body in accordance with machine directive 2000/14/EEC of the
European parliament and council.

Inspecting and monitoring organization: TÜV Österreich (Austrian technical inspectorate) Testing body no. 0408

Tab. 3-1 Sound power level

Measured sound power level 100dB (A)

NOTE The obligation to wear ear protection is standardized nationally. In Switzerland and Germany, this is as of a measured level of 85dB (A) (sound pressure).

3.4 Safety markings on the machine

● Observe and adhere to the rules.

● Keep the safety stickers and signs complete and legible.

● Replace any damaged or illegible stickers and signs immediately.

● You can order new stickers from Ammann Schweiz AG.

From the moment the signs are no longer recognizable and understandable at first
glance, the machine must be shut down until new signs are installed.

Warning stickers

Tab. 3-2 Warning stickers on board

Warning stickers Meaning

Location on roller:

Air intake opening/Inside of cowling

Danger:

Damage to electrical controls!

Explanation:

Never spray a water jet into electrical or electronic components.

Never spray into the engine combustion air intake.

Location on roller: Outer cowling cover.

Danger: Danger of injury due to incompetent operation:

Explanation: Read the operating instructions before operating the roller. Adhere to the safety regulations at all
costs. Contact your authorized dealer if anything is unclear.

Warning stickers Meaning

Location on roller: Between the front and rear parts of the roller.

Danger: Crushing hazard!

Explanation: Only stand in this area when necessary and only with extreme caution!

Location on roller: In the middle of the front and back.

Danger: Rollover hazard

Explanation: Only stand in this area when necessary and
only with extreme caution!

Location on roller: Radiator, both sides.

Danger: Warnings for cooling water radiator

Explanation: Do not put hands in the radiator fan when
the machine is running.

Notice stickers Meaning

Tab. 3-3 Notice stickers on board

Location on roller: Inner cowling cover.

Designation: If the roller has overturned, do not start the machine.

Explanation: Avoid oil shock.

Location on roller: Outer cowling cover.

Requirement: Wear ear protectors!

Explanation: Wear ear protectors in accordance with national accident prevention regulations when working at higher noise levels.

Notice stickers Meaning

Location on roller: Chassis rear

Designation: Guaranteed sound power level.

Explanation: Indicates the overall noise level produced by
the roller.

Location on roller: On the hydraulic oil tank

Designation: Hydraulic oil

Explanation: Please only use hydraulic oil indicated

Notice stickers Meaning

Location on roller: Chassis rear.

Designation: Hydraulic oil drain.

Explanation: Drain hole for the hydraulic oil

Location on roller: Chassis, front right.

Designation: Motor oil drain.

Explanation: Drain hole for the motor oil

Location on roller: Chassis rear.

Designation: Fuel.

Explanation: Filler neck for diesel fuel.

Location on roller: On the middle of the front and rear chassis

Designation: Tie-down point.

Explanation: Points on the roller at which lashing means
for securing the roller on the transport vehicle can be attached.

Location on roller: Roll bar, rear.

Designation: Suspension hooks.

Explanation: Points on the roller at which hoisting tackle
for lifting the roller can be attached.

Location on roller: Rear chassis, front upper left.

Designation: Lifting and tie-down points.

Explanation: Illustrates how the machine is to be loaded and transported.

Notice stickers Meaning

Location on roller: Rear chassis, front upper left.

Designation: Spare parts information

Explanation: Information about the filters of the machine

Location on roller: Inner cowling cover.

Designation: Close the cover.

Explanation: Attention: When driving using remote control and when parking the machine, the cover must be closed.

Location on roller: Inner cowling cover.

Designation: Ignition

Explanation: Attention: Current is present when the ignition is on.

3.5 Radiation compliance

This machine complies with the emission requirements for radio interference due to radiation, European Norm EN 13309, for construction machinery.


We know your business success depends on reliable quality equipment and parts to continue being a leader in your industry. When you want Genuine Multiquip / Mikasa original equipment parts, accessories and equipment you can always depend on Discount-Equipment.com to come through with the genuine o.e.m. products you need as quickly and inexpensive as possible. Our sales staff combined experience consists of over 90 years in the construction parts and equipment industry. We have over 1 million items online, if you are having trouble finding your item, we also have the resources to help you find what you need, our industry leading web site includes thousands of parts and service manuals available to look up your items. If you don't find what you are looking for please fill out our parts request form here.





Power Trowels

Picture of Walk Behind Power trowel

Shopping Cart

Your cart is empty


Manufacturer/Brand


Equipment Type




Over 32 Years of Serving the Industry





Edit this page