Gradall 534D9-45 Forklift Telescopic 45' 9,000lbs.

Operating Information

Please be sure to read the Safety information that accompanies this product.

Additional Safety & operating Instructions for Rough Terrain Forklift Trucks

(NOTE: In addition to safety and operating information for forklifts in general, the following information should be read and understood for rough-terrain/reach forklifts. This equipment is also referred to as telehandlers.)

Stability

Rough terrain forklift trucks which comply with the stability requirements are stable when properly operated. Improper operation, faulty maintenance, or poor housekeeping may contribute to a condition of instability.

Other conditions which may affect stability are:

ground and floor conditions
speed
dynamic and static forces
counterweight location
the judgment exercised by the operator
grade
loading
wheelbase
improper tire inflation

Rough terrain forklift trucks equipped with attachments must be operated as a partially loaded truck even when there is not a load on the attachment.

The amount of forward and rearward tilt to be used is governed by the application. The use of maximum rearward tilt is allowable under certain conditions, such as traveling with the load lowered. The stability of a rough terrain forklift truck does not encompass consideration for excessive tilt at high elevations or the operations of trucks with excessive off-center loads.

Operator Responsibility

You must be familiar with the operation and function of all controls and instruments before operating a rough terrain forklift truck.

Before operating the truck, read and be familiar with the operator’s manual for the particular truck being operated.

Check for adequate clearance before driving under electrical lines, bridges, etc.

General

Before starting to operate a rough terrain forklift truck:

Be in operating position and fasten seat belt.
Place directional controls in neutral.
Disengage clutch on manual transmission equipped rough terrain forklift trucks, or apply brake on power shift or automatic transmission-equipped trucks.
Start engine.

Do not start or operate the rough terrain forklift truck, any of its functions, or attachments from any place other than the designated operator’s position.

Traveling

When rough terrain forklift trucks are equipped with individual wheel brake pedals, lock pedal together for simultaneous operation before travel on public roads or when changing job sites.

For rough terrain forklift trucks equipped with a differential lock, the lock should not be engaged when driving on the road or at high speeds or when turning. If the lock is engaged when turning, there could be loss of steering control.

Loading

Improper use of stabilizer controls (if so equipped) could cause rough terrain forklift truck upset. Use stabilizers only in compliance with the manufacturer’s instructions.

For rough terrain forklift trucks equipped with lateral leveling:

Level the frame before raising the boom or mast, with or without a load.
Lateral leveling should not be used to position an elevated load -- lower the load and reposition the rough terrain forklift truck.

Handle only stable or safely arranged loads:
When handling off-center loads which cannot be centered, operate with extra caution
Handle only loads within the capacity of the rough terrain forklift truck
Handle loads exceeding the dimensions used to establish rough terrain forklift truck capacity with extra caution. Stability and maneuverability may be adversely affected.

Suspended Loads

The handling of suspended loads by means of a crane (boom) or other device can introduce dynamic forces affecting the stability of a rough terrain forklift truck that are not considered in the stability criteria. Grades and sudden starts, stops, and turns can cause the load to swing and create a hazard if not externally stabilized.

When handling suspended loads:

Do not exceed the truck manufacturer’s capacity of the rough terrain forklift truck as equipped for handling suspended loads.
Only lift the load vertically and never drag it horizontally.
Transport the load with the bottom of the load and the mast as low as possible.
With load elevated, maneuver the rough terrain forklift truck slowly and cautiously, and only to the extent necessary to permit lowering to the transport position.
Use tag lines to restrain load swing when ever possible.

Elevating Personnel

A rough terrain forklift truck should not be used to lift people unless there is no other practical option. If a rough terrain forklift truck must be used to lift people, the following precautions must be taken:

Provide a personnel platform which complies with the design requirements listed in the appropriate standard.
Securely attach the platform to the lifting carriage or forks.
Secure the lifting carriage and forks to prevent them from pivoting upward.
Deactivate the rotation on trucks equipped with rotation.
When moving parts of the rough terrain forklift truck pose a hazard to elevated personnel, provide appropriate protection.
Provide protection for personnel (in their normal working position on the platform) from moving parts of the rough terrain forklift truck that presents a hazard.
Provide overhead protection as needed by the operating conditions.
Lifting mechanisms need to operate smoothly through the entire lift range -- while loaded or unloaded.
All lift limiting devices and latches, if provided, need to be working properly.
Be certain that the mast or boom travel is vertical –do not operate on a side slope unless the rough terrain forklift truck is leveled.
Keep the platform horizontal. Never tilt platform forward or rearward when it is elevated.
Be certain that the forklift truck has a firm footing.
Be certain that required restraining means such as railing, chains, cable, body belt(s) with lanyard(s) etc., are in place and properly used.
Place rough terrain forklift truck control(s) in neutral and set parking brake.
Before elevating personnel, area should be marked to warn of work by elevated personnel.
Maintain a path of platform travel that is clear of hazards, e.g., storage racks, scaffolds, overhead obstructions, and electrical wires.
Keep hands and feet clear of controls other than those in use.
Always lower the platform, if you must move the forklift truck for adjustments in positioning.
Alert elevated personnel before moving the platform. Then move the platform smoothly and with caution.
A trained operator shall be in position to control the forklift truck or available to operate controls if the platform is not equipped with controls. The operator shall remain at the operator station if an employee is elevated.
The combined mass (weight) of the platform, load, and personnel shall not exceed one-third of the capacity at the rated load center position as indicated on the information plate(s) of the forklift truck on which the platform is used.
Personnel are to maintain firm footing on the platform. Use of railing, planks, ladders, etc., on the platform for purpose of achieving additional reach or height is prohibited.
Be certain that personnel and equipment on the platform do not exceed the available space.
Platform shall be lowered to floor level for personnel to enter and exit. Personnel shall not climb on any part of the rough terrain forklift truck in attempting to enter and exit.
Any body belt, lanyard, or deceleration device which has sustained permanent deformation or is otherwise damaged shall be replaced.
Prohibit modification to the platform that is detrimental to its safe use.

How a Forklift Works

Driving a forklift is different than driving a car
In a car or truck the front wheels steer the vehicle. A forklift has the steering wheels in the rear. The rear end of the forklift swings in a circle around the front wheels that support most of the load. The operator must check that there is room for the rear end to swing when making turns.

This clearance can be maintained in your workplace by permanently marking aisles with painted lines or arranging storage racks in a way that creates obvious aisles for travel.

However, these marked aisles will only be effective if you keep them clear of stored materials, which can gradually encroach as space is needed.

A forklift is not as responsive as a car when turning the steering wheel. Rear steering makes it difficult to stop a forklift quickly or swerve and still maintain control. It is important, then not to drive a forklift fast or round corners quickly.

Driving with the load downhill can result in loss of the load and control of the forklift.

Keep the load uphill to maintain control of the forklift.

If you drive a forklift on an incline, you must keep the load on the uphill side. Otherwise, you may have no weight on the wheels that steer and can lose control! The load could also fall off or cause the forklift to tip.

Often a large forklift load obstructs the driver’s view in one direction. It may be necessary to travel long distances with the load to the rear (in reverse for most forklifts). Use extra caution when traveling in reverse.

Forklift safety features
A backrest extension on the forks prevents part of the load from falling rearward toward the operator. This is required when loads are lifted high and the type of load would allow all or part of it to fall to the rear under conditions such as acceleration, sudden stops or driving on an uneven surface.

An overhead guard prevents an object on the forks or on a high rack from falling onto the operator while picking or placing a load at elevation. The guard is not designed to withstand the impact from a full load. It can be effective in deflecting small packages. It is required on all forklifts that can lift a load above the operator unless conditions such as clearances would not allow the forklift to be used.

Operator restraints will hold you in the seat if you strike an object or if the forklift overturns. Since 1992, forklift manufacturers have been required to equip new forklifts with operator restraints such as seat belts. Many forklift manufacturers offer restraint systems that can be retrofitted on older forklifts.

If your forklift begins to overturn, you are safest when you stay in the seat, hold on firmly, and lean in the opposite direction of the fall rather than trying to jump. Many fatal accidents happened when the operator tried to jump. As the forklift begins to tip, it will move slowly – tricking the operator into believing there is time to jump. Once the center of gravity is past the wheel line, the forklift will rapidly fall. The forklift’s overhead guard will quickly pin or crush an operator who jumps.

Failure to wear a seat belt can result in the operator being thrown outside the protective cage in the event of overturn.

If your forklift has a restraint such as a seat belt or a lap bar, you must use it.

How forklifts safely carry and lift heavy loads

A forklift works on the principle of a cantilever. A load on a beam (the forks) supported by a fulcrum (the front wheels) is counterbalanced by a weight on the other end of the beam (the forklift body and counterweight built into it).

Whether a forklift will safely carry a load or will tip forward can be determined by comparing the "moment" of each.

Moment equals the distance from the fulcrum to the center of gravity (the point where all the weight is concentrated) times the weight.

Example: an evenly distributed 36" wide load on the forks has a center of gravity that is 18" from the face of the forks. (Note: The fulcrum point is actually at the center of the wheel. Forklift load charts, however, are adjusted to allow measuring from the face of the forks.) If the load weighs 4000 pounds then the load moment will be (18" x 4000 lb.) = 72,000 inch-pounds.

If the "moment" of the forklift is greater than or equal to the 72,000 inch pounds of the load then the forklift will safely carry the load. Forklifts have a capacity plate to tell the user what loads are safe to lift. If the plate says the capacity is 30,000 pounds or less then that capacity is rated for a load with a center of gravity 24” from the face of the forks. If the forklift capacity is greater than 30,000 pounds then the label will rate the load at a 36" or 48" center of gravity since larger forklifts usually lift physically larger loads.

For example, a forklift rated at 5000 pounds would safely lift a load with a moment of up to (24" X 5000 lb.) = 120,000 inch-pounds. In this case the load above would be safe to lift.

Forklift Moment = (24" x 5000 lbs.) = 120,000 inch-pounds.

The load is safe to lift because load moment is less than forklift moment.

However if the 4000 pound load was 66" wide, the load moment would be (33" X 4000 lb.) = 132,000 inch-pounds which would be greater than the moment of the forklift. The forklift would tip forward.

As the load is raised, it becomes possible for the forklift to fall to the side as well as tip forward. The operator must consider the center of gravity of the forklift and load together. This combined center of gravity moves as the load is moved and as the forklift travels over surfaces that are rough or inclined.

Forklifts have a "stability triangle". The sides of the triangle as shown in the illustration are formed by the center of each front wheel and the center of the rear wheel or at the center of the axle if there are two rear wheels.

A vertical line extending from the center of gravity of the vehicle-load combination must be inside of the stability triangle to prevent the forklift from tipping forward, falling sideways or dropping its load.

The center of gravity of the forklift-load combination can move outside the stability triangle if:

The load is picked up on the tip of the forks,
The load is tilted forward,
The load is tilted too far back when raised,
The load is wide, or
Forklift movement causes the center of gravity to shift.

These actions will have the following effects:

Action	Center of gravity moves:
Tilting the load forward	Toward the front axle
Raising the load while tilted forward
Driving on an incline with the load downhill
Stopping forward travel or accelerating backward
Tilting the load back	Toward the rear axle
Raising the the load while tilted back
Driving on an incline with the load uphill
Accelerating forward or stopping backward travel
Driving across an inclined surface	Toward the downhill side of the triangle
Driving across a rough or uneven surface	Toward the rut or low side of the triangle
Turning	Toward the side now facing the original direction of travel

This list represents operator procedures that reduce the risk of overturn, collision or loss of the load.

To prevent your forklift from tipping over, falling sideways or dropping its load:

Make sure the load is stable and safely arranged on the forks.
Do not tilt the forks forward except when picking up or depositing a load.
Tilt the load backward only enough to stabilize the load.
Keep the load low just above the pavement with forks tilted back when traveling.
Cross railroad tracks diagonally when possible.
Enter elevators squarely.
Keep the load uphill when going up or down an incline.
Drive at a speed that will allow you to stop safely within the stability triangle.
Slow down on wet or slippery surfaces.
Slow down to make turns.
Avoid driving over loose objects or on surfaces with ruts and holes.

We know your business success depends on reliable quality equipment and parts to continue being a leader in your industry. When you want Genuine Gradall original equipment parts, accessories and equipment you can always depend on Discount-Equipment.com to come through with the genuine o.e.m. products you need as quickly and inexpensive as possible. Our sales staff combined experience consists of over 90 years in the construction parts and equipment industry. We have over 1 million items online, if you are having trouble finding your item, we also have the resources to help you find what you need, our industry leading web site includes thousands of parts and service manuals available to look up your items. If you don't find what you are looking for please fill out our parts request form here.