Click

Multiquip / Mikasa MVH158GH Reversible Plate, 17" Wide Plate, Honda GX200 Engine, 6070 lbs cf



Safety Information

Multiquip MVH158GH Reversible Plate Compactor

SAFETY INFORMATION

Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.
Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others

SAFETY MESSAGES

The four safety messages shown below will inform you about potential hazards that could injure you or others. The safety messages specifically address the level of exposure to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

GENERAL SAFETY

CAUTION

NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.

NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

NEVER operate this equipment under the influence of drugs or alcohol.

ALWAYS check the equipment for loosened threads or bolts before starting.

DO NOT use the equipment for any purpose other than its intended purposes or applications.

ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.

NOTICE

This equipment should only be operated by trained and qualified personnel 18 years of age and older.

Whenever necessary, replace nameplate, operation and safety decals when they become difficult read.

Manufacturer does not assume responsibility for any accident due to equipment modifications. Unauthorized equipment modification will void all warranties.

NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest fire extinguisher.

ALWAYS know the location of the nearest first aid kit.

ALWAYS know the location of the nearest phone or keep a phone on the job site.
Also, know the phone numbers of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency

COMPACTOR SAFETY

DANGER

NEVER operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fi re could result causing severe bodily harm or even death.

WARNING
NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CAUTION

NEVER lubricate components or attempt service on a running machine.

NOTICE

ALWAYS keep the machine in proper running condition.

Fix damage to machine and replace any broken parts immediately.

ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

ENGINE SAFETY

DANGER

The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

The engine of this equipment requires an adequate free flow of cooling air. NEVER operate this equipment in any enclosed or narrow area where free flow of the air is restricted. If the air flow is restricted it will cause injury to people and property and serious damage to the equipment or engine.

WARNING

DO NOT place hands or fingers inside engine compartment when engine is running.

NEVER operate the engine with heat shields or guards removed.

Keep fingers, hands hair and clothing away from all moving parts to prevent injury.

DO NOT remove the radiator cap while the engine is hot. High pressure boiling water will gush out of the radiator and severely scald any persons in the
general area of the compactor.

DO NOT remove the coolant drain plug while the engine is hot. Hot coolant will
gush out of the coolant tank and severely scald any persons in the general area of the compactor.

DO NOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the compactor.

CAUTION

NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing equipment.

NOTICE

NEVER run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction.

NEVER tamper with the factory settings of the engine or engine governor.
Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.

NEVER tip the engine to extreme angles during lifting as it may cause oil to gravitate into the cylinder head, making the engine start difficult.

FUEL SAFETY

DANGER

DO NOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fire due to static electricity.

DO NOT start the engine near spilled fuel or combustible fluids. Diesel fuel is extremely flammable and its vapors can cause an explosion if ignited.

ALWAYS refuel in a well-ventilated area, away from sparks and open flames.

ALWAYS use extreme caution when working with flammable liquids.

DO NOT fill the fuel tank while the engine is running or hot.

DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.

Store fuel in appropriate containers, in well-ventilated areas and away from sparks and flames.

NEVER use fuel as a cleaning agent.

DO NOT smoke around or near the equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a hot engine.

BATTERY SAFETY (ELECTRIC START ONLY)

DANGER

DO NOT drop the battery. There is a possibility that the battery will explode.

DO NOT expose the battery to open flames, sparks, cigarettes, etc. The battery contains combustible gases and liquids. If these gases and liquids come into contact with a flame or spark, an explosion could occur.

WARNING

ALWAYS wear safety glasses when handling the battery to avoid eye irritation.
The battery contains acids that can cause injury to the eyes and skin.

Use well-insulated gloves when picking up the battery.

ALWAYS keep the battery charged. If the battery is not charged, combustible gas will build up.

DO NOT charge battery if frozen. Battery can explode. When frozen, warm the battery to at least 61°F (16°C).

ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous concentration of combustible gases.

If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, rinse skin or clothing immediately with plenty of water.

If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty of water and contact the nearest doctor or hospital to seek medical attention.

CAUTION

ALWAYS disconnect the NEGATIVE battery terminal before performing service on the equipment.

ALWAYS keep battery cables in good working condition. Repair or replace all worn cables.

TRANSPORTING SAFETY

CAUTION

NEVER allow any person or animal to stand underneath the equipment while lifting.

NOTICE

Before lifting, make sure that the equipment parts (hook and vibration insulator) are not damaged and screws are not loose or missing.

Always make sure crane or lifting device has been properly secured to the lifting bail (hook) of the equipment.

ALWAYS shutdown engine before transporting.

NEVER lift the equipment while the engine is running.

Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

Use adequate lifting cable (wire or rope) of sufficient strength.

Use one point suspension hook and lift straight upwards.

DO NOT lift machine to unnecessary heights.

ALWAYS tie down equipment during transport by securing the equipment with rope.

ENVIRONMENTAL SAFETY/DECOMMISSIONING

NOTICE

Decommissioning is a controlled process used to safely retire a piece of equipment that is no longer serviceable. If the equipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost
effective to maintain (beyond life-cycle reliability) and is to be decommissioned (demolition and dismantlement),be sure to follow rules below:

DO NOT pour waste or oil directly onto the ground, down a drain or into any water source.

Contact your country's Department of Public Works or recycling agency in your
area and arrange for proper disposal of any electrical components, waste or oil
associated with this equipment.

When the life cycle of this equipment is over, remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling
batteries that contain sulfuric acid.

When the life cycle of this equipment is over, it is recommended that the frame and all other metal parts be sent to a recycling center.

Metal recycling involves the collection of metal from discarded products and its transformation into raw materials to use in manufacturing a new product.

Recyclers and manufacturers alike promote the process of recycling metal. Using a metal recycling center promotes energy cost savings.

EMISSIONS INFORMATION

NOTICE

The diesel engine used in this equipment has been designed to reduce harmful levels of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxides (NOx)
contained in diesel exhaust emissions.

This engine has been certified to meet US EPA Evaporative emissions requirements in the installed configuration.

Attempting to modify or make adjustments to the engine emission system by unauthorized personnel without proper training could damage the equipment or create an unsafe condition.

Additionally, modifying the fuel system may adversely affect evaporative emissions, resulting in fines or other penalties.

Emission Control Label

The emission control label is an integral part of the emission system and is strictly controlled by regulations.

The label must remain with the engine for its entire life.

If a replacement emission label is needed, please contact your authorized Kohler Engine Distributor.


We know your business success depends on reliable quality equipment and parts to continue being a leader in your industry. When you want Genuine Multiquip / Mikasa original equipment parts, accessories and equipment you can always depend on Discount-Equipment.com to come through with the genuine o.e.m. products you need as quickly and inexpensive as possible. Our sales staff combined experience consists of over 90 years in the construction parts and equipment industry. We have over 1 million items online, if you are having trouble finding your item, we also have the resources to help you find what you need, our industry leading web site includes thousands of parts and service manuals available to look up your items. If you don't find what you are looking for please fill out our parts request form here.





Power Trowels

Picture of Walk Behind Power trowel

Shopping Cart

Quote Queue

Multiquip/Mikasa MVH406DSZ, 28" Compactor, 12365lb, Hatz Diesel NLA

0603TU02EX Spacer, Short For TK MVP90 - GH5 Plate Compactor

Skid Steer, 2200 lbs. (Mustang 2076)

529937746 Husqvarna 30 187 1-3/8 PTBHP W1515-NNN DIAMOND TOOL WALLSAW BLADES (805544568401) Genuine OEM Husqvarna

542751758 Husqvarna 32 250 1-3/8 PTBHP W1410-NNN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544829595)

542773293 Husqvarna 36 250 1-3/8 PTBHP W1107 NWN HI PERF WALL SAW BLD WIDE Wallsaw Blades (805544623322)

826911GT KIT CONTROL BOX 50HZ Terex RL4 Horizontal Mast Light Tower

39615 02000 Instruction book Airman PDS185S-6B4 Air Compressor

582290402 Husqvarna 24 250 1" SBHP W1405 NWN SSW MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544985215)

Predator 836-1500303 T-Mag, 150 Grit (Blue), Double Round, Medium Bond

38440 21510 Shroud Fan Airman PDSF330DP and PDS400S-6E1 Air Compressor

529932303 Husqvarna 26 220 1DP LYBHP W1525-NNN DIAMOND TOOL WALLSAW BLADES (805544567336) Genuine OEM Husqvarna

39173 00700 Complete Drain Plates Airman PDS185S-6B4 Air Compressor

542773563 Husqvarna 30 235 LYBHP W1120 NWN HI PERF WALL SAW BLD WIDE Wallsaw Blades (805544677929)

TK MM8-E3.0 8 Cu. Ft. Mortar Mixer With 3 HP Electric Motor Plus Free Tow Pole

34210 30200 Casing Airman PDS185S-6C1 Air Compressor

249155 351112-30 ECM, DEEP SEA ELECTRONICS CONTROLLER, 4510 MKII, DSE 4510-003-35, AUTO START (4510-003-35) Genuine OEM

Predator 836-1500101 T-Mag, 150 Grit (Blue), Double Rectangle, X-Soft Bond

592880515 Husqvarna 36 235 1DP LYBHP W1520-NN HI PERF WALL SAW BLD WIDE Wallsaw Blades (805544486941)

FS Curtis Air Compressor Pump, 2-Stage 5 HP, 14.0 CFM, 175 PSI (E-35)

38100 46200 Radiator Airman PDSF330DP and PDS400S-6E1 Air Compressor

SPE 836-9003007 SPE 20ES Side Seal Bartell

227645GT ELECTRIC BOX 20KW 6L 4PTL Terex AL5 Light Tower

542776012 Husqvarna 32 250 LYBHP W1120 NWN HI PERF WALL SAW BLD WIDE Wallsaw Blades (805544377751)

592880312 Husqvarna 32 250 1DP LYBHP W1510-NN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544476997)

592880309 Husqvarna 32 187 1DP LYBHP W1510-NN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544476768)

A0000511660 Generac PowerFlex Cord Assembly Adapter 25ft 10/3 SOOW Input:5-20 Yellow Watertight 20A

249130 Inlet Valve for Winco 40/40 (MISC999) Genuine OEM Winco Products

529937719 Husqvarna 32 235 1DP LYBHP W1515-NNN DIAMOND TOOL WALLSAW BLADES (805544566087) Genuine OEM Husqvarna

33100 43810 Receiver Tank Airman PDS185S-6C1 Air Compressor

237120 Voltage Regulator Fuse for DE-30 (350005-401) Genuine OEM Winco Products

592880335 Husqvarna 63 220 1DP LY/PTBHP W1510-WN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544637886)

39670 Hub Cplg 1-1/8 x 1/4 - Elec for Toro/Stone Mixers

592880301 Husqvarna 24 187 1DP LYBHP W1510-NN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544476423)

529937753 Husqvarna 26 220 1DP LYBHP W1515-NNN DIAMOND TOOL WALLSAW BLADES (805544917933) Genuine OEM Husqvarna

03407 66819 Seal Rubber Airman PDS185S-6C2 Air Compressor

N/A GREASE FITTING CAP, (INCLUDED ON 0000GRH200) TK BBS20

529937720 Husqvarna 32 250 1" LY/PTBHP W1515-NNN DIAMOND TOOL WALLSAW BLADES (805544566230) Genuine OEM Husqvarna

590598701 Husqvarna 42 235 LYBHP W1525-NWN DIAMOND TOOL WALLSAW BLADES (0) Genuine OEM Husqvarna

839131GT KUBOTA FAN COVER Terex AL4 Light Tower

529932317 Husqvarna 48 250 1DP LYBHP W1525-NWN DIAMOND TOOL WALLSAW BLADES (805544567787) Genuine OEM Husqvarna

GX390UT2QZAV Honda 390CC HONDA ENGINE Genuine OEM Honda

EDCO 26300 BB-14 Masonry Saw, Gasoline, 5.5HP HONDA

GCV170LAG5BR-T114 Honda 170CC HONDA ENGINE VERTICAL Genuine OEM Honda

Saw, Masonry 20" blade guard 3HP. Elec. 230V (Stone MS2 01735)

Predator 836-0160104 T-Mag, 16 Grit (Grey), Double Rectangle, Hard Bond

39189 17100 Plate Airman PDS185S-6B4 Air Compressor

GX390RT2VXG Honda 390CC HONDA ENGINE Genuine OEM Honda

Bil-Jax 0064-0783 Half Outrigger Clamp

592880315 Husqvarna 36 235 1DP LYBHP W1510-NN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544477178)

Excavator Breaker Adapter (MEHA)

585148903 Husqvarna 40 235 1" PTBHP W1107 NWN DIAMOND TOOL WALLSAW BLADES (805544929097) Genuine OEM Husqvarna

542761291 Husqvarna 21 140 1DP LYBHP HH610 HI PERF HAND SAW BLD WET Wallsaw Blades (098526493031)

GX340UT2QXC9-BK Honda 340CC HONDA ENGINE Genuine OEM Honda

39189 17300 Plate Airman PDS185S-6B4 Air Compressor

585070003 Husqvarna 48 235 1-3/8 PTBHP W1410 MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544885881)

Predator 836-0800102 T-Mag, 70/80 Grit (Yellow), Double Rectangle, Soft Bond

592880304 Husqvarna 24 250 1DP LYBHP W1510-NN MAX PERF WALL SAW BLD NRW Wallsaw Blades (805544476485)

542776088 Husqvarna 32 250 LYBHP W1130 NWN HI PERF WALL SAW BLD WIDE Wallsaw Blades (805544380201)

GX390UT2XQC9 Honda 390CC HONDA ENGINE 49 STATE ENGINE Genuine OEM Honda


Manufacturer/Brand


Equipment Type




Over 32 Years of Serving the Industry